Tovább az oldal tartalmához

Keyboard stand

  • Foldable keyboard stand in Z-shape
  • For 2 keyboards
  • Exterior width: 53 to 91 cm
  • Interior width: 48 to 86 cm
  • Depth of the 1st support: 41 cm
  • Height adjustment of the 1st support: 59 to 92 cm
  • Depth of the 2nd support: 41 cm
  • Height adjustment of the 2nd support: 12 to 30 cm (measured from the 1st support)
  • Angle adjustable in 10° steps
  • Dimensions (folded up): 78 x 58 x 25 cm
  • Rubber pads for a secure hold
  • katalógusunkba bekerült: Július 2019
  • Termékszám 449542
  • mennyiségi egység 1 darab
  • Keyboard Supports 2
42 590 Ft
Minden ár tartalmazza az ÁFÁ-t
3-4 héten belül szállítható
1

110 Ügyfelek értékelései

4.4 / 5

stabilitás

kezelhetőség

kivitelezés

76 Vélemények

S
Ma is ugyan ezt venném... :)
SándorZoltán 06.10.2026
Anno nem kifejezetten csak az ára miatt választottam ezt, (le volt értékelve) de maga a kialakítása, és az anyaga (zártszelvény (és ebből adódóan a stabilitása / teherbírása)) műszaki szemmel nézve nagyon megtetszett.

Valamint nekem mindenképpen 2 soros állvány kellett, és a felsőre is mind méretben, és mind súlyban is egy komolyabb szinti is kényelmesem / biztonságosan elfér.
Az alsó és felső szint közötti távolság is állítható.
A felső szint több fokozatban, de racsnisan dönthető.
Filcet adnak a fém tartószerkezet és a szinti közé csúszásgátlásnak (öntapadósat).
Az alsó szint magassága is állítható és az egész állvány széessége is.
Szóval engem meggyőzött. :)
A napi használat során azóta sem csalódtam, s ma sem kellene se drágább, se jobb. :)
stabilitás
kivitelezés
kezelhetőség
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
i
Best Wallet Friendly option!
iannsk 17.06.2024
Pretty sturdy and and durable stand. Holds my weighty Korg Sv-1 pretty well. Both levels are also pretty wide to accommodate different boards. Screws tighten clamps around the adjustable legs and rods so as to not damage them (unlike those screws that screw on a single point on the legs/rods and damage them).


Do be careful of the screws though, the knobs are made of plastic and may have some sharp edges - a simple sanding and trimming does the trick.

Also, it would be great if there are standard heights settings for the 2nd tier extension. Bottom tier has them but the top doesn’t. Takes a little more effort to get the top tier to level out. Should be an easy fix DIY-ing holes.

All in all a pretty great and sturdy stand for both stage and/or studio use. Definitely recommend!
stabilitás
kivitelezés
kezelhetőség
1
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
KM
Not good at all , get something else
Kamil M 13.12.2021
Someone really not clever designed this to be honest , 2 synths on it and with a little push the whole stand will tip over to the back , weigh distribution extremely poorly designed. Avoid!
stabilitás
kivitelezés
kezelhetőség
8
3
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
A
Upper tier on the wrong side? Backwards design?
Anonim 09.05.2022
It seems to me that this was messed up in the design phase. As several other reviewers have noted, the center of gravity is too far backwards, and the feet stick out way way too far in the front.
I fixed this by flipping the whole thing backwards and using it without the upper tier. Maybe I will try to modify it to install the upper tier flipped to the other side.
stabilitás
kivitelezés
kezelhetőség
4
1
Jelentem!

Jelentem!