Tovább az oldal tartalmához

Angled Jack Plug

  • 2 - Pole
  • 6.3 mm
  • Colour: Silver
  • katalógusunkba bekerült: Március 2007
  • Termékszám 110748
  • mennyiségi egység 1 darab
  • Installation No
  • Mono/Stereo Mono
  • Angled Yes
  • Type TS (mono/unsym.)
  • Plug Jack 6,3 mm TS male angled
1 469 Ft
Minden ár tartalmazza az ÁFÁ-t
Mennyiségi kedvezmény
Darabár Megtakarítás Mennyiség
1 469 Ft 1
1 399 Ft 4,8% 10
1 349 Ft 8,2% 50
1 299 Ft 11,6% 100
Azonnal szállítható
1

855 Ügyfelek értékelései

4.8 / 5

kivitelezés

313 Vélemények

W
Etalon, telecasterhez jó
Winnetou 08.07.2020
Nagyon jó dolgozni vele, tökéletesen működik. Külön öröm, hogy telecaster süllyesztett aljzatához is megfelel, mert pont annyival lóg ki a kanyar, hogy jó legyen.
Nagyon vastag kábelekkel (pl. Sommer Cable The Spirit LLX - 7,5mm átmérő) is működőképes, csak olvasd el a használati utasítást, hogy hogyan kell lecsípni a belső műanyag inzert végét.
kivitelezés
1
0
Jelentem!

Jelentem!

A
Neutrik NP2 RX
Anonimuz 08.02.2026
Works well, quality is fine.
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
j
Best quality jacks - hands down
jrakus 30.09.2020
After years and years of soldering guitar cables I know why I buy Neutrik jacks.
They're not cheap but the money spent will get back to you. Trust me I try to find everything as cheap as I can. Cheaper jacks always come with problems. Try to unsolder a cheap jack and use it again... problems. You will also burn the inner insulation/plastic on a cheap jack if you're not careful. Never happened to me with Neutrik.
You can use the same Neutrik jacks again and again.

Neutrik got everything perfect. It's easy to solder, holds the cable well, very robust.
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
FM
An industry standard for a reason
Funeral Musician 22.01.2023
These plugs have an ingenious, time-tested strain relief, which works perfectly every single time, but the terminals inside of them are quite a bit closer to each other than on some of their competitors, so soldering a thicker cable to them is not as easy. It is not hard, but it is harder. Since I had never experienced any issues with these plugs, I ordered six of them for my home-made patch cables. When I opened the bags and inspected them, I noticed that on some of them, the molding of the strain relief was a little less precise than on others, and when I screwed them together, the parts did not fit together as well as before, and sometimes, there was an uneven gap between the metal body of the plug and the strain relief. I tried taking them apart and putting them back together a few times, but the issues persisted. In a moment of creativity, I even tried mixing and matching parts between plugs, but it did not help much. Then, I looked at the packaging the plugs had come in. Curiously, on some of them, it was written “Made in Liechtenstein”, while on others — “Designed in Liechtenstein”. Does that mean the manufacturing has been moved elsewhere? That would explain some of the plugs being lower quality. In any case, I will not be risking my money with the Neutrik plugs anymore. While all the six plugs were still functional, as a perfectionist, I want my cables to not only work but also look nice and tidy. In the past, the Neutrik plugs used to fulfill that request, but not anymore.
kivitelezés
0
0
Jelentem!

Jelentem!